Hinkley-lighting HOLBROOK 1797 User Manual download pdf

assembly instructions

Item No. 1797

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst installing the glass,

attaching mounting hardware to the junction box, making all necessary electrical

connections, attaching the ﬁxture to the wall.

start here

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Drawing 1 - Glass Installation

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then

refer back to this sheet to continue installation of this ﬁxture.

01.01.13

Drawing 2 - Fixture Mounting

1. Prepare threaded tube (C) by threading on hex nut (D) approximately 1/2”.

2. Thread tube (C) in mounting strap (A), approximately 1/4 “ - see Drawing 2.

3. Attach mounting strap (A) to junction box (J) using two screws (B) provided.

4. It will be necessary to adjust threaded tube (C). This is done by slippiing the mount-

ing hole (E) over threaded tube (C) and holding the ﬁxture against the wall. Adjust

threaded tube (C) until there is approximately 3/8” of thread showing inside the

ﬁxture. Remove ﬁxture from wall and tighten hex nut (D) against mounting bracket

(A) to secure threaded tube (C) in place.

1. To mount ﬁxture, slip center hole of backplate (E) over threaded tube (C) and hold

ﬁxture in position - see Drawing 1.

2. To complete assembly thread barrel knob (K) onto end of threaded tube (C) and

tighten.

3. Your ﬁxture can now be lamped accordingly.

1797

1. To install glass panels (2), slip them up through the open bottom of the cage (1).

- see Drawing 1.

2. Slip bottom of glass panels (2) into channel (3) in bottom of cage (1) tip, top of

panel into position, and bend down clips (4) to secure glass in cage. Repeat procedure

for remaining panels of glass.

H I N K L E Y L I G H T I N G 3300 0 Pi n Oa k Pa rkw a y Avon Lak e, O H 4 4012 8 00. 446. 5539 / 4 4.6 5 3.5 5 00 h inkl eyl i ght ing. com

1 2 3

Summary of Contents

Page 1 - Item No. 1797

assembly instructionsItem No. 17971. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. Carefully review instructions p

Page 2

HINKLEY LIGHTING 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.comI.S. 18 wiring grounding instr

Page 3 - Caulking Instruction____

I.S.200 Caulking Instruction____start here---Drawing

Comments to this Manuals

No comments

Hinkley-lighting HOLBROOK 1797 User Manual

Browse online or download User Manual for Lighting Hinkley-lighting HOLBROOK 1797. Hinkley Lighting HOLBROOK 1797 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Hinkley-lighting HOLBROOK 1797